Ebm-papst W3G630-GD03-A1 Uživatelský manuál stáhnout pdf (Strana 5)

Operating instructions

W3G630-GD03-A1

Translation of the original operating instructions

3.2 Nominal data

Motor M3G084-GF

Phase 1~

Nominal voltage / VAC 230

Nominal voltage

range / VAC

200 .. 277

Frequency / Hz 50/60

Type of data definition ml

Speed / min

-1

800

Power input / W 280

Current draw / A 1.2

Max. back pressure / Pa 75

Min. ambient temperature

/ °C

-25

Max. ambient

temperature

/ °C

ml = Max. load · me = Max. efficiency · fa = Running at free air

cs = Customer specs · cu = Customer unit

Subject to alterations

3.3 Data according to ErP directive

Installation category A

Efficiency category Static

Variable speed drive Yes

Specific ratio

1.00

Specific ratio = 1 + pfs / 100 000 Pa

Actual Request

2013

Request

2015

Overall efficiency ηes / % 42.3 25.8 29.8

Efficiency grade N 52.5 36 40

Power input Ped / kW 0.24

Air flow qv / m³/h 6570

Pressure increase total psf / Pa 52

Speed n / min

-1

805

Data definition with optimum efficiency.

The ErP data is determined using a motor-impeller combination in a standardised

measurement configuration.

3.4 Technical features

Mass 19.6 kg

Size 630 mm

Surface of rotor Coated in black

Material of blades Press-fitted sheet steel blank, sprayed

with PP plastic

Material of wall ring Sheet steel, pre-galvanised and coated in

black plastic (RAL 9005)

Material of guard grille Steel, coated in black plastic (RAL9005)

Number of blades 5

Direction of air flow "V"

Direction of rotation Counter-clockwise, seen on rotor

Type of protection IP 54; Depending on installation and

position

Insulation class "B"

Humidity class F3-1

Mounting position Shaft horizontal or rotor on bottom; rotor

on top on request

Condensate discharge

holes

Rotor-side

Operation mode S1

Motor bearing Ball bearing

Technical features - Output 10 VDC, max. 10 mA

- Alarm relay

- Motor current limit

- PFC, active

- Soft start

- Control input 0-10 VDC / PWM

- Control interface with SELV potential

safely disconnected from the mains

- Over-temperature protected

electronics / motor

- Line undervoltage / phase failure

detection

Touch current acc.

IEC 60990 (measuring

network Fig. 4, TN

system)

<= 3.5 mA

Motor protection Thermal overload protector (TOP) wired

internally

Cable exit Variable

Protection class I (if protective earth is connected by

customer)

Product conforming

to standard

EN 61800-5-1

Approval EAC

For cyclic speed loads, note that the rotating parts of the device

are designed for maximum one million load cycles. If you have

specific questions, contact ebm-papst for support.

3.5 Mounting data

For depth of screw, see chapter 3.1 Product drawing

; Secure the mounting screws against accidentally coming loose (e.g.

by using self-locking screws).

Strength class for

mounting screws

8.8

You can obtain additional mounting data from the product drawing if

necessary.

3.6 Transport and storage conditions

; Use the device in accordance with its protection type.

Max. permissible

ambient motor temp.

(transp./ storage)

+80 °C

Min. permissible

ambient motor temp.

(transp./storage)

-40 °C

Item no. 50431-5-9970 · Revision 83190 · Release 2014-06-26 · Page 5 / 12

ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com

1 2 3 4 5 6 7 8 9 10 11 12

Operating instructions 1

Komentáře k této Příručce

Žádné komentáře

Ebm-papst W3G630-GD03-A1 Uživatelský manuál Strana 5

Komentáře k této Příručce

Související produkty a manuály pro Hardware Ebm-papst W3G630-GD03-A1